This page contains links to third parties, if you click through those links we may receive a commission at no extra cost to you.

Engine Fault Code P0495

Fan Speed High

Care Engine Code Reader
The Engine Fault Code P0495 indicates that the engine control module (ECM) has detected a problem with the cooling fan speed. Specifically, it means that the fan is running at a higher speed than what the ECM expects. This can happen for several reasons, such as a faulty fan, a bad temperature sensor, or issues with the ECM itself.

While P0495 generally has the same meaning across various manufacturers, there can be slight differences in how it is interpreted or what might trigger it. Here are some alternative meanings or related issues based on different manufacturers:

1. Porsche: Similar to the general definition, but may also relate to specific fan control systems in high-performance models.

2. Mini: Often associated with cooling system issues, especially if the car is experiencing overheating.

3. Mercedes-Benz: Could indicate a problem with the auxiliary fan, which is important for high-performance cooling in their models.

4. Audi: May be linked to the dual cooling fan system, which is common in many Audi vehicles.

5. Jaguar: Might involve specific fan control modules that are unique to certain models.

6. Land Rover: Could indicate issues with the electric cooling fan, especially in off-road or high-load conditions.

If you encounter this code, its best to start by checking the fan operation, wiring, and relevant sensors. Always refer to the specific service manual for your vehicle for the most accurate diagnosis and repair steps.
The Engine Fault Code P0495 indicates that there is a problem with the cooling fan speed being too high. This code can arise from several issues, and while the general causes are similar across different manufacturers, there can be specific variations depending on the make and model. Here are some common causes:

1. Faulty Cooling Fan: The fan may be stuck in the `on` position due to a malfunction, causing it to run at high speed continuously.

2. Faulty Fan Relay: If the relay that controls the fan is stuck or malfunctioning, it can cause the fan to operate at high speed.

3. Wiring Issues: Damaged or shorted wiring in the fan circuit can lead to incorrect readings and cause the fan to run too fast.

4. Faulty Engine Control Module (ECM): In rare cases, the ECM itself might be faulty, leading to incorrect signals being sent to the fan.

5. Overheating Engine: If the engine is overheating, the cooling fan may run at high speed to try to cool it down. This could be due to a coolant leak, a bad thermostat, or a blocked radiator.

6. Faulty Temperature Sensor: If the coolant temperature sensor is faulty, it may give incorrect readings to the ECM, causing the fan to run at high speed.

Manufacturer-Specific Notes:

Porsche: Check for issues with the cooling system, as Porsche engines are sensitive to overheating. The fan control module can also be a common point of failure.

Mini: Mini vehicles often have complex electrical systems. Check for any software updates or recalls that might address fan control issues.

Mercedes: Mercedes models may have specific fan control modules that can fail. Additionally, the wiring harness can be prone to wear, leading to shorts.

Audi: Audi`s use of advanced climate control systems may mean that the issue could also be linked to the HVAC system, affecting fan operation.

Jaguar: Jaguars often have multiple cooling fans. Ensure that the correct fan is being monitored and check for issues in the fan control circuitry.

Land Rover: Land Rovers can have issues with the fan module, especially in older models. Check for any software updates that might affect fan operation.

If you encounter the P0495 code, its best to diagnose the issue thoroughly to avoid unnecessary repairs. Always consult the specific service manual for your vehicle for detailed troubleshooting steps.
The Engine Fault Code P0495 indicates that the engine control module (ECM) has detected a high speed condition for the cooling fan. This can happen in various European cars, including Porsche, Mini, Mercedes, Audi, Jaguar, and Land Rover. Heres how to troubleshoot and potentially fix this issue:

General Steps:

1. Check the Cooling Fan:
– Inspect the cooling fan for any physical damage or obstructions. Make sure it spins freely without any debris.

2. Inspect Wiring and Connectors:
– Look for damaged wires or loose connections in the fan circuit. Repair or replace any damaged components.

3. Test the Cooling Fan Relay:
– The relay controls the fan operation. Use a multimeter to check if the relay is functioning correctly. If its faulty, replace it.

4. Check the Temperature Sensor:
– The engine temperature sensor may be sending incorrect signals to the ECM. Test the sensor and replace it if necessary.

5. Scan for Additional Codes:
– Use an OBD-II scanner to check for any other related fault codes that may provide more context for the issue.

6. Inspect the ECM:
– If all else seems fine, the ECM itself might be malfunctioning. This is less common, but if the wiring and components are good, consider having the ECM tested.

Manufacturer-Specific Notes:

Porsche: Check for software updates for the ECM. Sometimes, manufacturers release updates that address fan control issues.

Mini: Look for any known issues with the fan control module. Some models have specific recalls or service bulletins regarding this.

Mercedes: The cooling system is complex. Verify that the auxiliary fan is functioning properly and check for any issues with the climate control system, as it can influence fan operation.

Audi: Some Audis have a two-speed fan. Ensure that both speeds are working correctly. You may need to test the fan motor directly.

Jaguar: Check the fuse related to the cooling fan. If the fuse is blown, it may indicate a short circuit or overload issue.

Land Rover: Inspect the engine cooling system for leaks or blockages that could cause the fan to run at high speed continuously.



Addressing P0495 typically involves a systematic approach to diagnosing the cooling fan system. Always refer to the specific service manual for your vehicle for detailed instructions and specifications. If you`re not comfortable performing these checks, consider consulting a professional mechanic.
Driving with a P0495 code, which indicates a high fan speed, can be concerning, but it depends on the specific vehicle and situation. Heres a breakdown of what it generally means and the safety considerations for the brands you mentioned:

General Overview:
– P0495 means that the engine control module (ECM) has detected that the cooling fan is running at a high speed when it shouldnt be. This could be due to a faulty sensor, a stuck relay, or an actual overheating issue.

Safety Considerations:
1. Overheating Risk: If the fan is running high, it might be trying to cool an overheating engine. If the engine is overheating, continuing to drive could cause serious damage.
2. Fan Operation: A continuously running fan could drain the battery if the vehicle is off for long periods.
3. Check Engine Light: If the check engine light is on, its a good idea to get it checked out soon to prevent further issues.

Manufacturer Specifics:
Porsche: Generally, its best to stop driving if the car shows signs of overheating. Check the coolant level and temperature gauge.
Mini: Similar to Porsche, if the engine temperature rises, stop driving. Mini engines can be sensitive to overheating.
Mercedes: Mercedes vehicles often have advanced cooling systems. If the fan is running high, it might not be an immediate danger, but have it checked soon.
Audi: Audi vehicles may have complex cooling systems. If you notice any performance issues, its wise to get it diagnosed.
Jaguar: Jaguars can be prone to overheating if there are cooling issues. Pull over and check for any warning lights.
Land Rover: High fan speeds could indicate cooling issues, especially in off-road conditions. Monitor the temperature gauge closely.


If you see a P0495 code, its best to have it diagnosed by a professional as soon as possible. While you might be able to drive the car for a short distance, its crucial to watch for signs of overheating and take action if necessary. Always prioritize safety and the health of your vehicle!

OBD Codes Explained

Engine Codes

P is for PowerTrain - Engine and Transmission.

P0 Indicates Generic Powertrain Codes

P0 Codes indicate problems with the powertrain and are common for all vehicles using the OBD-II Standard.

P1 Enhanced Manufacturer Specific Codes

P1 Codes are specific to manufacturers.

Sub-System

The 3rd Digit indicates the Sub-System

1 – Emission Management

2 – Injector Circuit

3 – Ignition

4 – Emission Control

5 – Vehicle Speed and Idle

6 – Computer and Output

7 – Transmission

8 – Transmission

9 – Reserved

0 – Reserved

0
    0
    Your Cart
    Your cart is emptyReturn to Shop

    Need parts advice?

    Tell us what you need and we will be in touch shortly.

    Contact Information
    Vehicle Information