This page contains links to third parties, if you click through those links we may receive a commission at no extra cost to you.

Engine Fault Code P0339

Crankshaft Position Sensor A Circuit Intermittent

Care Engine Code Reader
The Engine Fault Code P0339 refers to an issue with the crankshaft position sensor circuit. Specifically, it indicates that there is an intermittent problem with the signal from the crankshaft position sensor `A.` This sensor is crucial because it helps the engine control unit (ECU) determine the position of the crankshaft, which is vital for timing the ignition and fuel injection.

When you see this code, it means that the ECU is getting inconsistent information from the sensor. This can lead to poor engine performance, stalling, or difficulty starting the vehicle.

Possible Causes:
1. Faulty Crankshaft Position Sensor: The sensor itself may be malfunctioning.
2. Wiring Issues: Damaged or corroded wires and connectors can cause intermittent signals.
3. Poor Ground Connection: A bad ground can affect the sensor`s performance.
4. ECU Issues: In rare cases, the engine control unit itself may have a problem.

Alternative Meanings:
While P0339 generally refers to the crankshaft position sensor, some manufacturers might have slight variations in how they define this code. Here are a few examples:

– P0339 on Audi and Volkswagen: Similar to the general definition, but may also indicate specific issues with the sensor`s location or installation.
– P0339 on Mercedes-Benz: May relate to the sensor`s alignment or issues with the timing chain/belt.
– P0339 on Jaguar and Land Rover: Could suggest additional checks for the vehicle`s specific wiring harness or connectors.

If you encounter this code, it`s important to diagnose the specific cause. Start by checking the sensor and its connections, then move on to the wiring and ECU if needed.
The Engine Fault Code P0339 indicates an intermittent issue with the Crankshaft Position Sensor (CKP) A circuit. This sensor is crucial as it helps the engine control module (ECM) determine the position and speed of the crankshaft, which is essential for proper engine timing and fuel injection. Here are some common causes for this code:

1. Faulty Crankshaft Position Sensor: The sensor itself may be malfunctioning. This is often the most straightforward issue to check.

2. Wiring Issues: Damaged or frayed wiring in the CKP circuit can cause intermittent signals. Look for loose connections, corrosion, or breaks in the wires.

3. Connector Problems: Poor connections at the sensor or ECM can lead to intermittent signals. Ensure that the connectors are clean and securely attached.

4. Timing Belt or Chain Issues: If the timing belt or chain is worn or misaligned, it can affect the crankshaft position readings.

5. Faulty ECM: In rare cases, the engine control module itself may have a fault that causes it to misinterpret the signals from the crankshaft position sensor.

6. Magnetic Interference: Some vehicles may experience interference from nearby magnetic fields, which can affect sensor readings.

7. Oil or Dirt Contamination: Accumulation of oil or dirt on the sensor can also lead to incorrect readings.

Manufacturer-Specific Considerations:

Porsche: On some Porsche models, the sensor may be more sensitive to heat, so check for overheating issues or insulation breakdown.

Mini: Mini vehicles might have unique wiring harness issues due to compact engine bays, leading to wear and tear.

Mercedes: For Mercedes, ensure to check for software updates or recalls that might relate to the CKP sensor.

Audi: Audi vehicles may have more complex engine management systems, requiring a thorough diagnostic scan to pinpoint the issue.

Jaguar: Some Jaguar models may have specific sensor placement that can be affected by engine vibrations or movement.

Land Rover: In Land Rover vehicles, check for any recent modifications or repairs that might have disturbed the CKP circuit.

Always start with a thorough inspection of the sensor and its connections, and use a diagnostic scanner to gather more information if needed.
Fixing the Engine Fault Code P0339, which indicates an intermittent issue with the crankshaft position sensor (CKP), involves several steps. This code can appear in various European car brands like Porsche, Mini, Mercedes, Audi, Jaguar, and Land Rover. Heres a general guide, along with some manufacturer-specific notes:

General Steps to Fix P0339:

1. Check the Sensor:
– Locate the crankshaft position sensor. Its usually near the crankshaft or flywheel.
– Inspect the sensor for any visible damage or wear.

2. Inspect Wiring and Connectors:
– Check the wiring harness connected to the sensor for frays, cuts, or corrosion.
– Make sure the connector is clean and securely attached.

3. Test the Sensor:
– Use a multimeter to test the resistance of the sensor. Consult the vehicle`s service manual for specific resistance values.
– If the resistance is out of range, the sensor may need to be replaced.

4. Check for Other Codes:
– Use an OBD-II scanner to check for other fault codes. There might be related issues affecting the CKP sensor.

5. Inspect Timing Components:
– If the timing belt or chain is worn or misaligned, it can affect the crankshaft position sensor. Check these components for wear.

6. Clear the Code:
– After making repairs, clear the fault code with an OBD-II scanner and take the car for a test drive to see if the code returns.

Manufacturer-Specific Notes:

Porsche:
– For models like the Porsche 911, ensure that the sensor is properly aligned. A misaligned sensor can cause intermittent readings.

Mini:
– In Mini models, check for software updates that may address sensor issues. Sometimes, a simple software update can resolve the problem.

Mercedes:
– Mercedes vehicles may have multiple crankshaft sensors. Ensure you are testing and replacing the correct one. Also, check for any related issues in the engine control unit (ECU).

Audi:
– Audi models often have a specific procedure for replacing the CKP sensor. Refer to the service manual for detailed instructions.

Jaguar:
– For Jaguars, pay attention to the engine`s grounding. A poor ground connection can cause intermittent sensor signals.

Land Rover:
– Land Rover vehicles may have more complex wiring. Be thorough in checking all connections and consider using a wiring diagram for reference.

Final Tips:
– Always refer to the specific service manual for your vehicle for detailed instructions.
– If youre unsure or the problem persists, consider consulting a professional mechanic.
Driving with a P0339 code, which indicates an intermittent issue with the crankshaft position sensor (CPS), is generally not safe. This code means that the engine control module (ECM) is having trouble reading the crankshaft position sensor`s signal. Heres what you should know about the implications and some manufacturer-specific considerations:

General Implications:
1. Engine Performance: The crankshaft position sensor is crucial for the engine`s timing and performance. An intermittent signal can lead to rough idling, stalling, or difficulty starting the engine.
2. Check Engine Light: The check engine light will likely be on, which means theres a problem that needs addressing.
3. Potential Damage: Continuing to drive with this issue could lead to further damage or complications, especially if the engine stalls while driving.

Manufacturer-Specific Considerations:
1. Porsche: Driving with a P0339 code may cause performance issues, especially in models with high-performance engines. Its best to diagnose and fix it promptly.

2. Mini: Intermittent signals can affect the vehicle`s ability to start or run smoothly. It`s advisable to have the sensor checked as soon as possible.

3. Mercedes: In many Mercedes models, the CPS is critical for engine management. An intermittent signal could lead to misfires or even engine shutdown, so its important to address this quickly.

4. Audi: Similar to Mercedes, Audis rely heavily on the crankshaft position sensor for timing. An intermittent issue could lead to significant performance problems.

5. Jaguar: Jaguars also depend on the CPS for engine timing. An intermittent code could lead to stalling or starting issues, so repairs should be prioritized.

6. Land Rover: For Land Rovers, an intermittent CPS can affect off-road performance and engine management. Its best to have it checked to avoid getting stranded.


While you might be able to drive for a short time with a P0339 code, it is not advisable. The best course of action is to diagnose the issue and replace the crankshaft position sensor as needed. Ignoring it could lead to more serious problems down the line. If you experience any symptoms like stalling or rough idling, its best to stop driving and get it checked immediately.

OBD Codes Explained

Engine Codes

P is for PowerTrain - Engine and Transmission.

P0 Indicates Generic Powertrain Codes

P0 Codes indicate problems with the powertrain and are common for all vehicles using the OBD-II Standard.

P1 Enhanced Manufacturer Specific Codes

P1 Codes are specific to manufacturers.

Sub-System

The 3rd Digit indicates the Sub-System

1 – Emission Management

2 – Injector Circuit

3 – Ignition

4 – Emission Control

5 – Vehicle Speed and Idle

6 – Computer and Output

7 – Transmission

8 – Transmission

9 – Reserved

0 – Reserved

0
    0
    Your Cart
    Your cart is emptyReturn to Shop

    Need parts advice?

    Tell us what you need and we will be in touch shortly.

    Contact Information
    Vehicle Information